Call: (02) 8681 9790 (02) 8818 4883
The Model J2 Cable Lasher is used to lash a single aerial cable or numerous cables to a supporting strand or to an existing lashed cable with stainless steel lashing wire.
- Will lash any single or multiple aerial cables up to 3 in. (76mm) diameter across on any suspension strand from 1/4 in. (6mm) to 7/16 in. (11mm). A factory modification will allow the lasher to accommodate 1/2 in. (12.7mm) strand if necessary.
- Consists of a rotating drum supported on a carriage that provides the mounting for a driving mechanism, cable lifters, cable and strand rollers
- Each of two recessed magazines will hold a 1200 ft. coil of .045 in. (365m of 1.1mm wire) lashing wire (or 450 ft. of .065 in.). The Lashing Wire is fully recessed and covered by a gate.
- Features a fast setup procedure, quick coil loading, and automatic drum lock for easy span transfers and smooth forward travel
- Cable Lasher Parallel Pull Accessory P/N 70467
J2 Lashers make overlashing easy. Just push down on the strand roller knob, rotate it a quarter turn and you can lash additional cables together on previously lashed cable
- Positive internal gear to gear mechanism has no chains or belts to stretch, slip or break
- Constructed with heat-treated, plated steel, stainless steel, brass and aluminum components. Contains sealed and oiless bearings to minimize maintenance and assure durability.
- Pre-drilled and tapped at the factory for mounting of the lasher guard or “halo”. For use when lashing in overgrown areas.
- The J2 and every GMP lasher is fully serviceable to “good-as-new” specifications at our factory and at factory-trained service locations around the globe.
- The lasher is furnished with a rugged lightweight storage chest with corrosion resistant hardware, recessed latches and a moisture-proof, tongue-in-groove design for maximum protection when not in use
- Supplied with a 6 ft. bridle rope assembly and snap hooks, and an information and operation manual
Related Products
VFL 5KM 10km 15km 30km vfl 30mw Kit vfl 50km Visual Fault Locator
₱0
Product name | FTTH visual fault lcoator |
Wavelength | 650nm±10nm |
Emitter Type | FP-LD laser |
Output power | 5KM,10KM,30KM ect |
connector | 2.5mm universal adapter |
Working mode | Both CW and Pules available |
Operating temperature | -10~+45 °C |
Storage temperature | -40~+70 °C |
Power | 2pcs AA battery |
Working hours | 60 |
Weight | 78g (excluding batteries) |
Dimension (mm) | 168 X 27 |
Selling Units | Single item |
Single package size | 20X13X5 cm |
Single gross weight | 0.12 kg |
Package Type | packing by a plastic box then in a carton |
DVP 740 Fusion Splicer Machine
₱60,000
DVP 740 Fusion Splicer Machine
A DVP 740 Fusion Splicer Machine is an essential tool in the field of fiber optic communications, used to join two optical fibers end-to-end. The primary goal of splicing is to create a continuous optical path with minimal loss and reflection, ensuring efficient signal transmission.
KEVLAR ELECTRONIC SCISSOR
₱0
KEVLAR ELECTRONIC SCISSOR
Features
• Lightweight shears ideal for cutting Kevlar® strength members found in fiber optic cable construction
• Ergonomic molded handles provide comfort for both right and left handed users
• One micro-serrated blade reduces slippage for more positive cutting action
• Blades made from high carbon molybdenum and vanadium steel for long life
| Length | 14cm/5.5 inch |
| Material | 3CR13 stainless steel |
| Features | Resistant , tough , corrosion damage, lasting sharpness |
| Characteristic | Non-slip silicone handle , comfort grip , beautiful color lasting |
| Application | Apply to cut every kind of Kevlar of optical fiber, for FTTH site construction, factory production etc.. |
C-CORP 12 IN 1 OTDR
₱0
Features:
1.Expert OTDR: Professional measurement, curve/list/map are displayed simultaneously.
2.Auto OTDR: no complex settings, one key test.
3.OPM supports CW/270/330/1k/2kHz frequency identification.
4.VFL and LS can run in the background, multi task can be operated simultaneously.
5.LS supports CW/ modulation mode output with adjustable output power.
6.RJ45 cable tracker of digital radar, stronger anti-jamming ability.
7.Auto OTDR, expert OTDR, event map, OPM, LS, VFL,RJ45 cable sequence, 8.RJ45 cable tracker, RJ45 cable sequence, RJ45 cable length, end face detection, flash light optical loss test.
9.RJ45 cable sequence, cable length test, up to 300m.
10.One click screen capture, easy to save the interface.
11.Support ILOM.
12.Support SC/APC
- Auto OTDR
- Expert OTDR
- Event Map
- Optical Power Meter (OPM) -50 +26
- Laser Source (LS)
- Visual Fault Locator (VFL) 10m W 10km
- RJ45 Cable Sequence
- RJ45 Cable Tracker
- RJ45 Cable Length (up to 300m)
- End Face Detection
- Support ILOM
- Support SC/APC SC/UPC
- Wavelength 1310/1550
- Dynamic Range 26/24dB
- Test Range 100km Event Blind Zone 2.5m
- ATT Blind Zone 8m
- 4.3 inches IPS TFT LCD Touch Screen
- Lithium Battery 3.7V 4000mAh
- SOR Standard File Format
FTTH FLAT DROP CABLE JACKET STRIPPER
₱0
FTTH FLAT DROP CABLE JACKET STRIPPER
Product Specifications:
Construction | Description |
Adapt To Optical Fiber | Single-core silica optical fiber |
To Adapt Optical Fiber Coating Diameter | φ0.25 & φ0.9 |
Adapt To The Bare Fiber Diameter | 125μm |
Cutting The Fiber Length | 10~16mm (φ0.25) 10~ 16 mm(φ0.9) |
Dimensions | 107mm (W) × 94mm (D) × 50mm (H) |
Weight | 325g |
Cutting Angle Adaptation Value | ≤0.7° |
Edge Life | 60000 times |
8PK-325 Round Cable Slitter
₱0
8PK-325 Round Cable Slitter
Cutter Slitting And Ringing Hand Tools
Strip cable with 4.5-25mm diameter
Optical Light Source (OLS)
₱0
SNP3109 optical light source can provide 1 to 4
output wavelengths to meet specific requirements,
including the 650nm red source and the
1310/1550nm wavelengths for single mode fiber or
the 850/1300nm wavelengths for multimode fiber,
as well as other wavelengths according to customer
needs. Together with the SNP3208 optical power
meter, it is a perfect solution for the fiber optic net-
work characterization.
OPTICAL POWER METER
₱0
This Optical Power Meter is an economical type highly cost-effective portable power meter. It can be used for the optical power measurement within the wavelength 800~1700nm. It also has a wide measurement range which is more than 70dB. It’s designed with the common wavelength calibration points, such as 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. The instrument is widely used in fiber-optic link construction, testing and maintenance.
High quality Miller Loose Buffer Tube Stripper/Mid-Span Access Tool 0.9mm to 3.0mm Fiber Optical Stripper
₱0
High quality Miller Loose Buffer Tube Stripper/Mid-Span Access Tool 0.9mm to 3.0mm Fiber Optical Stripper
Quick Details
- Model Number: AUA-05 stripper
- Type: Optical cable stripper, Optical Fibers
- Place of Origin: Shanghai, China
- Brand Name: DSEE
- Use: FTTH
- Warranty Time: 1 year
- Model Number:: wire stripper multi tool
- Access tube sizes: 0.9mm to 3.0mm
- key feature: Shaves precise opening to prevent fiber damage
- original country::: the U.S.A
- Use::: FTTH
- Application:: FTTH FTTB FTTX Network
- Weight:: 1.36 oz (38.5g)
- Application: FTTH
Reviews
There are no reviews yet.